Welcome to Käferland

Your online shop for VW Beetle spare parts

Established in 1987, Käferland is a specialist mail order company stocking OE (Original Equipment), NOS (New Old Stock), reproduction parts and our own manufactured parts (marked with KLF for Kaeferland Frankfurt)

The phone staff at Käferland are experts in Volkswagen restoration and will be happy to answer any questions regarding your restoration project. If you have problems locating a certain part, please give us a call.

Käferland is in no way affiliated with Volkswagen Werk AG or Volkswagen of America. The use of Volkswagen names and their model names, descriptions, and/or numbers are used in applications and descriptions for reference purposes only. Their use in no way denotes or infers a direct connection between Käferland and any vehicle manufacturer or their authorized agencies.


Drive System

Frame

Body Components

Mechanics

Interior

Electrical

Accessories

Our Catalog

In our main catalog you will find over 6,000 articles on 384 pages and more than 2,500 illustrations in color.

Useful information and technical tips about the beetle make this catalog a reference book.

Order it...

New
Drum spindle to disc brake conversion kit from year 08/65 (not 1302/1303)
Usually converting a ball joint front axle from a drum brake to a disc brake on the front axle is fairly easy. Unfortunately, the steering knuckles required for the conversion are very rare and sought after, so that implementation quickly runs into difficulties in procuring parts. The manufactured adapter plates enable the installation of a disc brake system on a vehicle with drum brakes without replacing the steering knuckles. Brake discs, wheel bearings and brake calipers correspond to the standard parts so that a reliable supply of wearing parts is also guaranteed. The scope of delivery includes two adapter plates, high-strength screws with locking washers and two brake lines. If necessary, the master brake cylinder must also be replaced.

€239.00*
Engine case, 1300-1600ccm
This is a new crankcase made from magnesium AS41. Cylinder studs M8 can be used.

€1,350.00*
Ignition timing light 12V
- for ignition timing adjustment and checking - suitable for all 12-V petrol engines, where ignition time adjustment is technically possible - ignition signal output via terminal for 1st Cylinder - bright stroboscope lamp provides good readability of the ignition time marking

€42.00*
Rear Quarter Panel right, Top Quality, year 50 - 07/55
With 3 water drainages and a complete B-pillar like the Original. Height a bit over 200mm

€109.00*
Rear Quarter Panel left, Top Quality, year 50 - 07/55
With 3 water drainages and a complete B-pillar like the Original. Height a bit over 200mm

€109.00*
Support panel under rear cross member, right, Top Quality, year thru 07/55
This reinforcement for the left cross member under the rear seat up to year 07/55 offers good quality and is made of 1.25 mm steel, just like the original. The precisely manufactured reinforcement plate is welded directly onto the rear cross member and corresponds to the fits for split, hermaphrodite and early oval beetles.

€48.00*
Support panel under rear cross member, left, Top Quality, year thru 07/55
This reinforcement for the left cross member under the rear seat up to year 07/55 offers good quality and is made of 1.25 mm steel, just like the original. The precisely manufactured reinforcement plate is welded directly onto the rear cross member and corresponds to the fits for split, hermaphrodite and early oval beetles.

€48.00*
Outer front cross panel, Top Quality, year 50 - 08/67
Nice quality made from 1mm sheet metal.

€98.00*
Inner front cross panel, Top Quality, year 50 - 08/59
Nice quality made from 1mm sheet metal. The correct rivet nuts for high beam switch are already installed. Also fits up to year 08/67 if the high beam switch with screw connections is used.

€249.00*
New
Outer door skin right, lower section, Top Quality, year 50 - 07/57
The height is 13 cm and comes with a joining lip to old metal.

€59.00*
New
Outer door skin left, lower section, Top Quality, year 50 - 07/57
The height is 13 cm and comes with a joining lip to old metal.

€59.00*
New
Lower inner section for ribbed door, right, Top Quality, year 10/52 - 07/55
Made of 1 mm thickness steel, very stiff. Hinge can be riveted to inner panel when door is cut for repair. Holes for the inner strengtener need to be drilled prior hinge assembly.

€229.00*
New
Lower inner section for ribbed door, left, Top Quality, year 10/52 - 07/55
Made of 1 mm thickness steel, very stiff. Hinge can be riveted to inner panel when door is cut for repair. Holes for the inner strengtener need to be drilled prior hinge assembly.

€229.00*
New
Headliner installation tool
Blade made of stainless steel, handle of birch wood. Made according original tool # 736

€59.00*
New
Heat insulation flange for Weber 40 IDF
Dual carb engines often have problems with vapor locks due to heat up carburettors. You can avoid this by using heat insulation flanges which isolate the carbs from the manifolds. The also needed paper gaskets are individually available, so you can re-use the insulation flanges. One set is for one throttle and comes with paper gaskets.

€9.00*
New
Steering knuckle, up to year 07/65, right, with collar bolt (overhauled)
The hub carrier is measured using original tools and subjected to a complete inspection. The tested components are then glass bead blasted and painted. All wearing parts are replaced with new parts. The deposit of 200 euros is included in the purchase price. The deposit will be refunded to you once you return a rebuildable old part. The old part must be delivered free of grease. ATTENTION: For uncleaned old parts, we charge a cleaning fee of 25.00 euros

€398.00*
New
Steering knuckle, up to year 07/65, left, with collar bolt (overhauled)
The hub carrier is measured using original tools and subjected to a complete inspection. The tested components are then glass bead blasted and painted. All wearing parts are replaced with new parts. The deposit of 200 euros is included in the purchase price. The deposit will be refunded to you once you return a rebuildable old part. The old part must be delivered free of grease. ATTENTION: For uncleaned old parts, we charge a cleaning fee of 25.00 euros

€398.00*
New
Manifold Heat Riser Insulation Kit, for dual heat riser intake manifold, year 08/73 on
If you've ever wondered why there is a space to screw something on your engine cylinder tin behind the heat riser of your intake manifold, Then you may be missing the piece of tin that covers the heat riser base. This kit includes enough pieces for your motor. The material is asbestos free.

€12.00*
New
Multimeter
Measuring ranges: - DC voltage 200 mV - 2 V - 20 V - 200 V - 600 V - AC voltage 200 V - 600 V - Resistance 200 Ohm - 2K Ohm - 20 KOhm - 200 KOhm - 2 MOhm - Direct current 20 µA - 200 µA - 2 mA - 20 mA - 200 mA - 10 A

€14.80*
New
Ring spanner S-shape SW12/13
Due to its special shape, this key is indispensable for hard-to-reach screws and nuts. Practical examples of applications include carburetors, fuel pumps, distributors and intake manifolds.

€8.00*
New
Brake fluid collection bottle 1 liter
This bottle with a capacity of one liter is indispensable when bleeding the brakes and allows used brake fluid to be easily disposed of.

€19.00*
New
Hose clamp
The hose clamp enables the reliable clamping of petrol hoses and plastic lines thanks to its swiveling clamping bracket made of robust metal, ensuring safe handling.

€5.00*
New
Brake line wrench, SW 10 / 11
A double offset wrench for loosening and tightening brake lines. The open and reinforced hexagon ensures maximum power transmission.

€10.00*
New
Window installation tool
With this tool, pulling the pull cord into the window rubber is very easy. The cord slides through the tube and in no time you can stretch the cord around the windshield. -with 6 m nylon cord -for mounting rubber-mounted, non-glued vehicle windows

€18.00*
New
Ring spanner C-shape SW11/13
Due to its special shape, this key is indispensable for hard-to-reach screws and nuts. Practical examples of applications include carburetors, fuel pumps, distributors and intake manifolds.

€6.50*
New
Reinforced hose for grease guns
The flexible armored hose is compatible with our grease gun, which has the item number 9055. It makes it easy to lubricate even hard-to-reach grease nipples.

€4.00*
New
Lever grease gun
The hand lever grease gun is ideal for lubricating the front axle. To reach hard-to-reach places, the use of the reinforced hose with item number 9055-S is recommended.

€29.90*